Difference between revisions of "IBHNet:Technical Data IBH Link S5++"
From IBHsoftec Wiki English
(Created page with " == Features == * S5 PU Connections * Fetch/Write Connections * RFC1006 for S7 HMI devices * Diagnostic LEDs * RJ45 * Power supply directly from the PLC * Passive PLCs also...") |
(→LED-Meaning) |
||
| Line 82: | Line 82: | ||
| Ready || On || Device Ready | | Ready || On || Device Ready | ||
|- | |- | ||
| − | | || | + | | || Flashing || Bootvorgang |
|- | |- | ||
| − | | Busy / Error || | + | | Busy / Error || On || Error |
|- | |- | ||
| || Flashing || Boot Process | | || Flashing || Boot Process | ||
| Line 94: | Line 94: | ||
'''The ''IBH Link S5++'' only requires 24 VDC if not supplied by the PLC. The external terminal needs to be supplied with 0V, the internal terminal with 24V DC. Pay attention to polarity.''' | '''The ''IBH Link S5++'' only requires 24 VDC if not supplied by the PLC. The external terminal needs to be supplied with 0V, the internal terminal with 24V DC. Pay attention to polarity.''' | ||
| − | |||
| − | |||
== Electrical data == | == Electrical data == | ||
Revision as of 08:32, 16 July 2012
Features
- S5 PU Connections
- Fetch/Write Connections
- RFC1006 for S7 HMI devices
- Diagnostic LEDs
- RJ45
- Power supply directly from the PLC
- Passive PLCs also possible with integrated 24V connector
Interfaces
| Interface | Type | Factory settings |
|---|---|---|
| Ethernet | 10/100MBPs, Auto Negotiation | 192.168.1.13 |
| USB-Device | Fullspeed (12 MBits/s), Ethernet Emulation, Powered by Device | 192.168.167.12 |
| UART | 20mA (TTY / Current Loop) | 9600 Baud |
| Power supply | 3.81mm, 2 Polig |
D-SUB15
| PIN | Signal | Meaning |
|---|---|---|
| 1 | GND | |
| 2 | TXD-Out | Open-Collector Out |
| 3 | N.C. | N.C. = not connected |
| 4 | Ext. | 5V-In external supply |
| 5 | N.C. | |
| 6 | +3.3V | |
| 7 | RXD-In | |
| 8 | N.C | |
| 9 | 3.3V-R | Connected with 3.3V over resistor 165 Ohm |
| 10 | GND | |
| 11 | N.C. | |
| 12 | N.C. | |
| 13 | N.C. | |
| 14 | N.C. | |
| 15 | N.C. |
LED-Meaning
| LED | State | Meaning |
|---|---|---|
| LINK / ACTIVITY | Flashing | Activity Ethernet |
| SPEED | On | 100MBps Ethernet |
| FDX / COLL | On | Full Duplex Ethernet |
| Ready | On | Device Ready |
| Flashing | Bootvorgang | |
| Busy / Error | On | Error |
| Flashing | Boot Process |
Attention
The IBH Link S5++ only requires 24 VDC if not supplied by the PLC. The external terminal needs to be supplied with 0V, the internal terminal with 24V DC. Pay attention to polarity.
Electrical data
| Parameter | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Power supply | 8 | 12 | 30 | V (DC) |
| Power consumption | 1 | W | ||
| Current (USB) | <20 | mA | ||
| Operating temparature | 0 | 60 | °C | |
| Storage temperature | -25 | 75 | °C | |
| Protection | IP20 |
Mechanical data
| Parameter | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Length | 58 | mm | ||
| Width | 42 | mm | ||
| Height | 18 | mm | ||
| Weight | 43 | g |
