Jonas: Created page with "The chart below shows the differences to S7-hardware PLC diagnostic buffer entries: {| class="wikitable" |- ! Diagnostic buffer entries !! Driver !! Description |- |style="wi..."

2013-01-23T10:05:19Z

Created page with "The chart below shows the differences to S7-hardware PLC diagnostic buffer entries: {| class="wikitable" |- ! Diagnostic buffer entries !! Driver !! Description |- |style="wi..."

New page

The chart below shows the differences to S7-hardware PLC diagnostic buffer entries:

{| class="wikitable"
|-
! Diagnostic buffer entries !! Driver !! Description
|-
|style="width: 8em"| 0xA000 ||style="width: 12em"| CIF PROFIBUS® || CIF-PROFIBUS®-card could not be initialized.
|-
| 0xA001 || CIF PROFIBUS® || Timeout during startup.
|-
| 0xA002 || CIF PROFIBUS® || Parameter inappropriate for CIF-Task
|-
| 0xA003 || CIF PROFIBUS® || Timeout during hot start
|-
| 0xA004 || CIF PROFIBUS® || Error when reading CIF-Firmware info
|-
| 0xA005 || CIF PROFIBUS® || Error when reading CIF-driver status
|-
| 0xA006 || CIF PROFIBUS® || Error when writing a message into the CIF-card
|-
| 0xA007 || CIF PROFIBUS® || Error when writing a message from the CIF-card
|-
| 0xA008 || CIF PROFIBUS® || Fehler bei PROFIBUS® Diagnose (PG)
CIF-Fehlercode
|-
| 0xA009 || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA00A || CIF PROFIBUS® || Timeout during hot start
|-
| 0xA00B || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA00C || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA00D || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA00E || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA00F || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (PU)
CIF-error code
|-
| 0xA010 || CIF PROFIBUS® || No CIF-driver installed
|-
| 0xA011 || CIF PROFIBUS® || CIF-PROFIBUS®-card could not be initialized
|-
| 0xA012 || CIF PROFIBUS® || CIF-PROFIBUS®-card not available
|-
| 0xA013 || CIF PROFIBUS® || Bus parameters for slaves could not be set
|-
| 0xA014 || CIF PROFIBUS® || Parameterisation of the CIF-PROFIBUS®-card with SDB-Daten failed
|-
| 0xA015 || MPI® || MPI®-telegram error
|-
| 0xA016 || CIF PROFIBUS® || Error in PU communication via PROFIBUS®
|-
| 0xA017 || CIF PROFIBUS® || Error in PU communication via PROFIBUS®
|-
| 0xA018 || CIF PROFIBUS® || Error in PU communication via PROFIBUS®
|-
| 0xA019 || CIF PROFIBUS® || Timeout in input data exchange with the CIF-card during SFC DPRD_DAT
|-
| 0xA01A || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (SFC/SFB)
CIF-error code
|-
| 0xA01B || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (SFC/SFB)
CIF-error code
|-
| 0xA01C || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (SFC/SFB)
CIF-error code
|-
| 0xA01D || CIF PROFIBUS® || Error at PROFIBUS® Diagnostics (SFC/SFB)
CIF-error code
|-
| 0xA020 || CIF PROFIBUS® || Error in input data exchange with the CIF-card during SFC DPRD_DAT
|-
| 0xA021 || CIF PROFIBUS® || Timeout in output data exchange with the CIF-card during SFC DPWR_DAT
|-
| 0xA022 || CIF PROFIBUS® || Error in output data exchange with the CIF-card during SFC DPWR_DAT
|-
| 0xA023 || CIF PROFIBUS® || CIF-PROFIBUS®-card could not be detected
|-
| 0xA024 || CIF PROFIBUS® || CIF-PROFIBUS®-card could not be initialized
|-
| 0xA025 || MPI® || MPI®-telegram error
|-
| 0xA050 || CIF 30/50/60 || No CIF-driver installed
|-
| 0xA051 || CIF 30/50/60 || CIF-card could not be initialized
|-
| 0xA052 || CIF 30/50/60 || CIF-card not available
|-
| 0xA053 || CIF 30/50/60 || Timeout during cold start
|-
| 0xA054 || CIF 30/50/60 || Application could not be set to operational mode "READY"
|-
| 0xA055 || CIF 30/50/60 || Error in I/O-data exchange with the CIF-card during PII/PIQ update
|-
| 0xA056 || CIF 30/50/60 || Error in input data exchange with the CIF-card during T PI
|-
| 0xA057 || CIF 30/50/60 || Error in output data exchange with the CIF-card during T PQ
|-
| 0xA058 || CIF 30/50/60 || Error reading CIF-Task-mode
|-
| 0xA05A || CIF 30/50/60 || CIF-card could not be initialized
|-
| 0xA05B || CIF 30/50/60 || CIF-card could not be initialized
|-
| 0xA060 || CIF 30/50/60 || Error reading CIF-Task-mode
|-
| 0xA061 || CIF 30/50/60 || Error accessing the watchdog
|-
| 0xA062 || CIF 30/50/60 || CIF-driver not in operational mode "COM"
|-
| 0xA063 || CIF 30/50/60 || DevExchangeIO in ClearOutputs failed
|-
| 0xA064 || CIF 30/50/60 || Error reading CIF-driver status
|-
| 0xA065 || CIF 30/50/60 || Error reading CIF-driver status
|-
| 0xA069 || CIF 30/50/60 || Timeout in I/O-data exchange with the CIF-card during PII/PIQ update
|-
| 0xA070 || CIF 30/50/60 || Timeout in input data exchange with the CIF-card during L PI
|-
| 0xA071 || CIF 30/50/60 || Timeout in output data exchange with the CIF-card during T PQ
|-
| 0xA072 || CIF 30/50/60 || Timeout in input data exchange with the CIF-card during SFC DPRD_DAT
|-
| 0xA073 || CIF 30/50/60 || Error in input data exchange with the CIF-card during SFC DPWR_DAT
|-
| 0xA074 || CIF 30/50/60 || Timeout in input data exchange with the CIF-card during SFC DPRD_DAT
|-
| 0xA075 || CIF 30/50/60 || Error in output data exchange with the CIF-card
|-
| 0xA080 || CIF 30/50/60 || CIF-driver not ready
|-
| 0xA081 || CIF 30/50/60 || CIF-driver not in mode "RUN"
|-
| 0xA082 || CIF 30/50/60 || CIF-driver not in mode "COM"
|-
| 0xA090 || CIF30X || CIF-driver not ready
|-
| 0xA091 || CIF30X || CIF-driver not in mode "RUN"
|-
| 0xA092 || CIF30X || CIF-driver not in mode "COM"
|-
| 0xA100 || TwinCAT I/O || Port number from PLC43.INI, not available in TwinCAT task
Subsequent value is returned from TCatIoOpen
|-
| 0xA101 || TwinCAT I/O || Error in PLC43.INI
Periphery start < byte start
|-
| 0xA102 || TwinCAT I/O || PII/PIQ update during startup failed
|-
| 0xA103 || TwinCAT I/O || Error in PLC43.INI
Periphery < process image
|-
| 0xA104 || TwinCAT I/O || Timeout when connecting to TwinCAT driver
Subsequent value is returned from the last function
|-
| 0xA105 || TwinCAT I/O || TwinCAT driver not in RUN
Subsequent value is returned from the function TCatGetState()
|-
| 0xA106 || TwinCAT I/O || TwinCAT driver update ClearOutputs failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA107 || TwinCAT I/O || TwinCAT driver update PII failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA108 || TwinCAT I/O || TwinCAT driver update PIQ failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA109 || TwinCAT I/O || TwinCAT driver update LoadPI failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoInputUpdate
|-
| 0xA10A || TwinCAT I/O || TwinCAT driver update StorePY failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA10B || TwinCAT I/O || TwinCAT driver update while retriggering data failed (driver not in RUN anymore)
Subsequent value is returned from the TwinCAT function
|-
| 0xA10C || TwinCAT I/O || Saving the changed configuration during startup failed.
Subsequent value is returned from the function
|-
| 0xA10D || TwinCAT I/O || TCatIoInputUpdate reports 'Busy' during refreshing the inputs
|-
| 0xA10E || TwinCAT I/O || TCatIoInputUpdate reports 'Busy' during refreshing the inputs
|-
| 0xA10F || TwinCAT I/O || TwinCAT driver update PII failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA110 || TwinCAT I/O || TwinCAT driver update StorePQ failed (driver not in RUN anymore)
Subsequent value is returned from the function TCatIoOutputUpdate
|-
| 0xA111 || TwinCAT I/O || TCatIoGetInputPtr failed
|-
| 0xA112 || TwinCAT I/O || TCatIoGetOutputPtr failed
|-
| 0xA113 || TwinCAT I/O || ADS communication thread could not get local address and was closed. No ADS communication possible.
Next value is returned from the function __AdsGetLocalAddress,if value is 0, then __AdsPortOpen has failed
|-
| 0xA114 || TwinCAT I/O || AdsSyncReadReq in FDL communication failed
|-
| 0xA115 || TwinCAT I/O || AdsSyncWriteReq in FDL communication failed
|-
| 0xA116 || TwinCAT I/O || AdsSyncReadReq in FDL communication failed
|-
| 0xA117 || TwinCAT I/O || AdsSyncWriteReq in FDL communication failed
|-
| 0xA118 || TwinCAT I/O || AdsSyncWriteReq in FDL communication failed
|-
| 0xA119 || TwinCAT I/O || TCatIoOutputUpdate reports 'Busy' during refreshing the outputs
|-
| 0xA120 || Softnet PN IO || Softnet error code of function PNIO_set_mode followed by the
Softnet error code
|-
| 0xA121 || Softnet PN IO || Softnet error code of function PNIO_controller_open followed by
Index of the controller
Softnet error code
|-
| 0xA122 || Softnet PN IO || Callback-error code for "mode change confirmation" followed by the
Softnet error code
|-
| 0xA123 || Softnet PN IO || Callback-error code for "device activate confirmation" followed by the
Softnet error code
|-
| 0xA124 || Softnet PN IO || Softnet error code of function PNIO_close followed by the
Softnet error code
|-
| 0xA126 || Softnet PN IO || Error in initialising of the Softnet PN IO driver
|-
| 0xA127 || Softnet PN IO || Softnet error code of function PNIO_set_mode operate followed by the
Softnet error code
|-
| 0xA128 || Softnet PN IO || Driver needs too much time to get into operate mode during initialization
|-
| 0xA140 || Addidata || Addidata error code
Subsequent value is returned from an ADDIPACK function
|-
| 0xA141 || I/O Port || No I/O Port access permitted by OS
|-
| 0xA148 || IBSPCI4 || Out of range error
|-
| 0xA149 || IBSPCI4|| openMXIDevice failed while opening the interbus board
|-
| 0xA14A || IBSPCI4 || closeMXIDevice failed while closing the interbus board
|-
| 0xA14B || IBSPCI4 || openDTIDevice failed while opening the interbus board
|-
| 0xA14C || IBSPCI4 || closeDTIDevice failed while closing the interbus board
|-
| 0xA150 || CIFX || Error in Profinet Diagnostics
|-
| 0xA151 || CIFX || Error in Profinet Diagnostics
|-
| 0xA152 || CIFX || Error on reset channel
|-
| 0xA153 || CIFX || Error on reset channel
|-
| 0xA154 || CIFX || Error on reset channel
|-
| 0xA155 || CIFX || Error in SFB 52 'RDREC'
|-
| 0xA156 || CIFX || Error in SFB 53 'WRREC'
|-
| 0xA161 || CIFX || Error on loading cifX driver
|-
| 0xA162 || CIFX || Error on sysdevice open
|-
| 0xA163 || CIFX || Error on channel open
|-
| 0xA164 || CIFX || Error on reset channel
|-
| 0xA165 || CIFX || Error on access host state
|-
| 0xA166 || CIFX || Error on access bus state
|-
| 0xA167 || CIFX || Error on reading input area PII
|-
| 0xA168 || CIFX || Error on writing output area PIQ
|-
| 0xA169 || CIFX || Error on reading periphery input area
|-
| 0xA16A || CIFX || Error on writing periphery output area
|-
| 0xA16B || CIFX || Error setting the watchdog
|-
| 0xA16C || CIFX || Error in xChannelIORead of SFC14
|-
| 0xA16D || CIFX || Error in xChannelIORead of SFC15
|-
| 0xA16F || CIFX || Error in xChannelInfo
|-
| 0xA170 || CIFX || Timeout starting the bus
|-
| 0xA171 || CIFX || Timeout starting the bus
|-
| 0xA172 || CIFX || Error in xSysdeviceInfo of SFC14
|-
| 0xA173 || CIFX || Error in xSysdeviceInfo of SFC15
|-
| 0xA174 || CIFX || Error initializing the Profibus board
|-
| 0xA175 || CIFX || Error deleting the Sycon.NET configuration.
|-
| 0xA176 || CIFX || Error configuring the card, make sure no .nxd file exists
|-
| 0xA177 || CIFX || Error configuring bus parameters
|-
| 0xA178 || CIFX || Error in Profibus Diagnostics
|-
| 0xA179 || CIFX || Error in Profibus Diagnostics
|-
| 0xA17A || CIFX || Error in Profibus Diagnostics
|-
| 0xA17B || CIFX || Error in Profibus Diagnostics
|-
| 0xA17C || CIFX || Error in Profibus Diagnostics
|-
| 0xA17D || CIFX || Error in Profibus Diagnostics
|-
| 0xA17E || CIFX || Error activating/deactivating slaves
|-
| 0xA17F || CIFX || Error in Profibus Diagnostics SFC13
|-
| 0xA180 || CIFX || Error in SFC 59 'RD_REC'
|-
| 0xA181 || CIFX || Error in SFC 58 'WR_REC'
|-
| 0xA182 || CIFX || Error in SFB 52 'RDREC'
|-
| 0xA183 || CIFX || Error in SFB 53 'WRREC'
|-
| 0xA184 || CIFX || Error in Profibus Diagnostics
|-
| 0xA185 || CIFX || Error in xChannelExtendedStatusBlock
|-
| 0xA186 || CIFX || Error in xChannelExtendedStatusBlock
|-
| 0xA187 || CIFX || Error in xChannelExtendedStatusBlock
|-
| 0xA188 || CIFX || Error in xChannelExtendedStatusBlock
|-
| 0xA189 || CIFX || Error reconfiguring the card
|-
| 0xA18A || CIFX || CifX device driver < 0.946 and/or profibus firmware < 2.3.22.5
|-
| 0xA190 || CIFX || Error analyzing the Profinet configuration
|-
| 0xA191 || CIFX || Error analyzing the Profinet configuration
|-
| 0xA192 || CIFX || Error retrieving the slave handles
|-
| 0xA193 || CIFX || Timeout during Profinet configuration occured
|-
| 0xA194 || CIFX || Error in configuration message of the Profinet configuration occured
|}

S7-SoftPLC:Diagnostic buffer entries - Revision history

Jonas: Created page with "The chart below shows the differences to S7-hardware PLC diagnostic buffer entries: {| class="wikitable" |- ! Diagnostic buffer entries !! Driver !! Description |- |style="wi..."