Andreas: Created page with "== Reading data from the SINUMERIK ONE == ==== Reading out the '''NCK''' data via the web interface ==== Insert a new station in the web interface using the '''Insert Sinumer..."

2023-12-22T09:51:14Z

Created page with "== Reading data from the SINUMERIK ONE == ==== Reading out the '''NCK''' data via the web interface ==== Insert a new station in the web interface using the '''Insert Sinumer..."

New page

== Reading data from the SINUMERIK ONE ==
==== Reading out the '''NCK''' data via the web interface ====

Insert a new station in the web interface using the '''Insert Sinumerik''' button.
The IP address and the slot of the '''NCK''' must be specified:

[[Image:IBH_Link_UA_CNC_ONE_Read_Model.png|329px]]

The SINUMERIK model can now be read out automatically.
The data read from the SINUMERIK ONE then appears under '''OPC Slots'''. The data model corresponds to the current model of the OPC Foundation:

[[Image:IBH_Link_UA_CNC_ONE_Slots.png|492px]]
 
 
 

=== Reading out the '''NCK''' data with the IBH OPC UA Editor ===

After the IBH Link UA has been created, a new '''CNC''' station can be inserted:

[[Image:IBH_Link_UA_CNC_ONE_CNC_Add_Station.png|521px]]

The IP address and the slot of the '''NCK''' must be specified:

[[Image:IBH_Link_UA_CNC_ONE_CNC_Add_Station_Dialog.png|438px]]

The variables can now be selected and the properties can be edited:

[[Image:IBH_Link_UA_CNC_ONE_CNC_Select_Variables.png|957px]]

Once the configuration is complete, it can be loaded into the IBH Link UA:

[[Image:IBH_Link_UA_CNC_ONE_CNC_Upload_Configuration.png|577px]]
 
 
 
 

=== Reading out the '''PLC''' data with the IBH OPC UA Editor ===
After the IBH Link UA has been created, a new '''controller''' can be inserted:

[[Image:IBH_Link_UA_CNC_ONE_CNCPLC_New_Control.png|549px]]

As the integrated PLC is a NCU 1750 CPU '''1518F-4''' PN/DP, the S7-1500 TCP/IP protocol must be selected:

[[Image:IBH_Link_UA_CNC_ONE_PLC_New_Control_Dialog.png|631px]]

The variables can either be created manually or the corresponding TIA project can be assigned:

[[Image:IBH_Link_UA_CNC_ONE_PLC_Assign_Program.png|547px]]

The variables can now be selected and the properties can be edited:

[[Image:IBH_Link_UA_CNC_ONE_PLC_Select_Variables.png|1244px]]

Once the configuration is complete, it can be loaded into the IBH Link UA:

[[Image:IBH_Link_UA_CNC_ONE_PLC_Upload_Configuration.png|572px]]
 
 
 

The following configuration settings must be observed when accessing the NCU 1750 CPU '''1518F-4''' PN/DP '''without fail''':

Under '''Protection''' allow full access and allow access via PUT/GET communication:

[[Image:IBH_Link_UA_CNC_ONE_Protection.png|1098px]]

The '''Optimized block access''' must be deactivated for the DB`s you want to have access to, or the data from an '''optimized''' DB must be copied in the PLC program, e.g. with an FC/FB, into a DB without optimization:

[[Image:IBH_Link_UA_S7_DB_properties.png|790px]]

IBH Link UA:SINUMERIC ONE - Revision history

Andreas: Created page with "== Reading data from the SINUMERIK ONE == ==== Reading out the '''NCK''' data via the web interface ==== Insert a new station in the web interface using the '''Insert Sinumer..."